7mm:1ft - 0 Gauge Railway Modelling.

Manufactured by: Body kit by Colin Waite
Remainder scratch built. 

Passenger Luggage Van. - Introduction            PDF version

finished, painted and ready for the roadThis is to be part of a train that includes the Finney 7 3232 Class 2-4-0, a Blacksmith Diagram E24 Brake Composite, plus a Blacksmith 38' brake third and a Colin Waite V2 PLV.


The basis for this vehicle is an old Colin Waite bodyline kit I bought years ago at the "Bring & Buy" stand at Telford.   The body had been mostly built and presented no real problems being very similar in construction to the E24, but smaller.  The parts all fitted together well and the etching is up to the standard one expects from such an illustrious source.

The Build

body in need of workbody in need of work 2These pictures of the body shew it needs some further work, having been built before the days I learned to do as much "in the flat" as possible.     Back to Top


The window bars need to be removed (indeed they were replaced with better ones from CPL) too so that the glazing can be fitted.   In due course, I corrected and completed it.


underframe startedHowever, it needed a complete under frame building from scratch.  This was started by making up the solebars from brass angle and the buffers beams from solid strip; soldered together with a centre spacer.

offering up the solebars to the bodyThe buffers and couplings are from CPL while the rivet detail on the buffers planks and step are from a sheet of etched parts from the old IKB range.


The frame must be square in both planes but this is relatively easy using the steel RSU plate and magnets to hold the part together while soldering. This is a job that has not been well planned (it was started at least two years ago!) and so this should be read as a master class in how NOT to scratch build.


A method of fixing the frame to the body was tackled next.  Two pieces of 2mm x 6mm brass strip were cut to fit between the solebars and two more to fit inside the body.  One of each was then lined up and clamped together while pilot holes were drilled.  The pieces to fit into the body were drilled and tapped 8BA; the other pieces were drilled to clear.  The relevant parts were then soldered into the body and across the the frame.


The frame was clamped to the body using the tapped pieces and 8BA bolts, taking care to line the frame with the body.  Then the tapped lengths were soldered in from the inside of the body, resulting in a strong and accurate fixing.  However, one of the consequences of "making it up as you go a long" is that the fixing bolts are now just a tad close to the wheels!           Back to Top


more components ready for the underframeThe 18' wheelbase was marked in and a set of CPL lost wax, long J hangers, springs and axle boxes soldered in place.  Some W irons from the spares box were soldered in behind them.

fabricating a floorAt this stage, I thought the solebars looked rather bare so fabricated some overlays using 0.2mm x 6mm phosphor bronze strip, pressing bolt head details from behind.  


foot board supports fittedOnce the overlays were fitted, eight Slater's footboard supports had the pins cut off and filed nice and flat before being soldered in place.

underframe slowly getting its bits fittedThe wheels are to be mounted in WEP compensated units.   The vacuum cylinder and brake gear will need a firm base to sit on so a partial floor of nickel silver was next fitted.  This is held in place with a few strips of 4mm brass angle.  It is probably much over engineered but I like things to be robust.


The wheels are set in WEP compensation units; the vacuum cylinder unit is from Cavalier in white metal.  The brake rods are glued into the adjustable rod pullers but soldered to the floor of the vehicle for strength.

The gas tank was turned up in the lathe from some oversize brass stock and has modified Blacksmith white metal ends glued on with Loctite 480.

complete and ready for the paint shopThe central support member had to be removed to fit the vacuum cylinder (yet another consequence of "making it up as one goes along!") but, now the floor is fitted, does not affect the strength or rigidity of the frame.


The next job is to assemble the clasp brake shoes and fix them in place before soldering the step boards on.  In fact, I fixed the step boards before the brakes.


The brakes were cobbled together from some spare IKB etched sheets I had to hand but still obtainable from the Broad Gauge Society).  I had also to fill the gaps in the floor so that my Heath-Robinson mounting system would work.                             Back to Top


The Van is now complete and ready for delivery to Dennis's paint shop.

painted now end view 1painted, detail end view 2
							Back from the paint shop, it is clear that Dennis has done a great job in bringing it to life.  Once painted the windows were fitted and the new window bars (CPL) fitted to all but the guard's door.






Here it is paired with the V2 (ex Colin Waite kit) van, also painted by Dennis.

paired with the V2 VanThey were satisfying to build, run well and look great, even if they are far too clean, (even for 1900ish), but that's how my customer wants them and the customer is always right.

Back to Top